注油器系列
概述
??箱體用不銹鋼制成，泵體采用仿美鋁制技術，油箱口部設計有回油和防塵機構，軸聯結部位采用獨特的防漏結構，減速箱采用鋰基潤滑脂潤滑，從而實現了工作過程中的零漏油，造型美觀，經久耐用。是提升潤滑技術水平的理想產品。
性能和技術參數
??正常工作壓力 ——40MPa(出口M10X1)
??最大注油量——0.37ml/r
??工作電壓 ——380V
??電機轉速 ——1400r/min
??防爆電機的防爆等級 ——ExdⅡBT4
安裝及外形尺寸
??將支架用螺絲鎖定或焊接在機床的某個部位即可?
??寬度 Width——230mm
??高度 Height——400mm
??長度根據泵體的頭數而變化
使用須知
注油器使用與保養
??1、注油器的工作介質采用運動粘度在50度時為17～4000cst的潤滑油，油液的過濾精度不低于0.025mm，或采用80目的鋼絲網過濾。
??2、注油量的大小可油注油泵上的調節螺套調節。16MPa、32MPa、48MPa注油泵順時針旋轉、注油量減少，反時針旋轉，注油量增大，調定后應將其鎖緊，以防調節螺套在工作時松動而使注油量發生變化。
??3、油箱內應注入經過過濾的潤滑油后，方可搖動手把，將泵體及管路中的空氣排除，即輸油管部有油滴出，方可接上主機注油點進行工作。當油箱內油面降低至最低油位時，應及時補充潤滑油。
??4、視油罩用于觀察滴油情況，使用中應保持清潔和防止破裂，不得隨意拆卸以免影響使用。注意視油罩不可用汽油清洗。
??5、注油器應定期用清潔煤油進行清洗，除去注油泵和油箱內部的雜質和污物。對于連續工作狀態下的注油器一般每隔一個月應清洗一次。

注油器常見故障及排除方法

General

??Tank-body is made of stainless steel, Pump-body adopt technology of aluminum from America. Mouth of gasoline tank design the structure of oil return and dust-proof. Part of axis joint adopt particular structure of antileak. Reducing gear box adopt lithium grease to lubricate, so it is zero leak wear, which is ideal product for improving lubrication technology.

Performance and technical parameters

??Normal working pressure——40MPa(M10×1)
??Max oil supply flux——0.37ml/r
??Working voltage——380V
??Rotation speed of motor——1400r/min
??Classification of anti hazard motor——Exd II BT4

Installment dimension

??Lock with screw or weld bracket to machine part.
??Width——230mm
??Height——400mm
??Length is varied according to head quantity of pump

Working direction
??Use and maintain of oil ejector
??1、 Working medium of ejector adopt lubricant of 17~4000cst when kinematic viscosity at 50. Filter precision of oil no less than 0.025mm, or adopt steel net of 80 holes to filter.
??2、 Amount of oil ejecting may be adjusted through adjusting turn buckle of filling pump. Amount of filling reduce when filling pump of 16MPa, 32MPa, 40MPa rotate clockwise; Amount of filling increase when it rotate antilock wise , locking it after adjusting in order to avoid variety of amount of filling due to adjusting thumbtack loosening during working .
??3、 Handle can be shaken to exhaust air in the pump body and pipe after filling lube filtered, e.g. end of oil pipeline drip oil, then connect filling point of principal machine to work. It must complement to lube in time when oil level lower the least in the gas oiline box.
??4、 Watching oil cover which is used to observe circus of drip oil must be clean and no break during use. It can’t be dismantle at random because use could be affected.
Note: Watching oil cover can’t be washed with gas oline.
??5、 Oil ejector must be washed with clean kerosene to eliminate impurity and ordure of filling pump and inner of gas oline box regularly. Usually oil ejector which is continuously used should be once washed every two months.

??Ordinary fault and work out method for oil ejector．